Electrical Installations Technology Practice Test

These questions are part of the practice quiz. Start practicing

• Which article covers luminaires and lighting outlets?
• MCCB stands for which term?
• Economy 7 is a tariff where power used at night is cheaper. Which heater type commonly uses this tariff?
• How many socket circuits are typically installed in a residential installation and why?
• Which cable type is commonly used in public buildings such as schools and offices?
• Which statement best describes the practical difference between two-plate (junction) and three-plate (loop-in) lighting systems?
• Which option identifies a ladder rack as a cable tray type?
• What is the main purpose of a service disconnecting means?
• Are cables allowed to be run side by side?
• What is the basic construction of a radiant heater?
• Which correction factor corresponds to ambient temperature?
• Which statement accurately describes THHN and THWN insulation types?
• Which statement best describes the function of the equipment grounding conductor?
• Which statement defines a fault in overcurrent context?
• From a ring circuit, how is the number of unfused spur outlets limited?
• Which statement describes a branch circuit?
• Are both MICC and FP200 fire resistant?
• Alarm systems wired in parallel are typically Open circuits. Which system type is commonly wired in this way?
• Which voltage is typical for distribution to supply a medium-sized factory with a private substation?
• Which statement best describes the function of the main protective bonding conductor?
• Which statement best describes the effect of GFCI protection?
• Which factor is not typically considered when sizing branch-circuit conductors?
• Which PVC cable type is generally used for wiring domestic installations?
• Earth leakage is current flowing into the ground; how does it differ from overcurrent?
• Which circuit type requires monitoring and how is it achieved?
• In bonding, what is the primary safety purpose of connecting exposed conductive parts?
• What should happen when overcurrent occurs due to earth leakage?
• The 400kV transmission voltage is described as:
• In a typical dwelling, what conductor connects the service equipment to the earth and to all bonded metal parts?
• Which NEC article covers signs and outlines of electric signs?
• What does voltage drop refer to in branch circuits?
• Where would you find calculations for maximum demand and diversity?
• Where is an End-of-Line resistor placed in a monitored alarm circuit?
• RCCB stands for which electrical protection device?
• HASAWA is the acronym for which Act?
• Which non-statutory guide expands on the 18th Edition?
• Which LAN cable category supports frequencies up to 100 MHz and is most common today?
• Which type of underfloor heating is used for small spaces?
• Mineral-insulated (MICC) cables use which insulating material?
• Which statement about fire systems wiring is true?
• Name three types of electrical drawings used in installations.
• Where should you look to find the protective device rating for an A3 radial final circuit?
• Which statement describes a Maintained emergency lighting system?
• What is the difference between overcurrent and overload?
• MCB stands for which term?
• What is meant by bonding a water pipe to the electrical system?
• Which document contains more specific examples for electrical installation practice?
• In the example circuit, which fuse should operate first if a fault occurs in the kettle?
• What is diversity in relation to electrical installations?
• Which statement accurately differentiates thermoplastic and thermosetting?
• Which distribution voltage is stepped down for typical use in homes?
• Why do tamper circuits and detector circuits have different polarities?
• PVC trunking over fire exits requires what?
• Which NEC article covers branch circuits and receptacle outlets?
• CDM Regulations refer to which of the following?
• Which statement correctly describes circuit protective conductors (CPCs)?
• A B40 MCB will typically trip in which current range?
• Which device is typically used to verify grounding continuity?
• What is the amp range in which you may be unable to let go of an electrified object?
• What is the main difference between conductor insulation temperature rating and operating environment?
• How long must emergency lighting stay illuminated for in an emergency?
• RCD stands for which term?
• Which NEC article covers receptacles, cord-and-plug-connected equipment?
• What is the purpose of an overcurrent protection device?
• Why is insulation temperature rating included when determining conductor capacity?
• Which statement explains why larger machinery can trip a B-type MCB even if the nominal current is correct?
• Why is distance important when sizing branch-circuit conductors?
• Which statement accurately describes MCCB compared to MCB?
• Discrimination and Selectivity are used interchangeably in protection discussions. Which statement best reflects their relationship?
• What is the difference between service grounding and equipment grounding?
• CBR stands for which term?
• Why are freestanding cookers typically fed directly from the CCU?
• When is neutral-ground bonding typically performed?
• What is the typical color of the grounding conductor in many systems?
• How does a transformer affect voltage and current?
• Which voltage is listed as a transmission voltage?
• In PUWER, the 'WE' stands for what?
• Which statement is true about stainless steel compared with galvanised steel?
• Which statement accurately contrasts thermoplastic and thermosetting?
• In a 120/240 V residential system, which colors typically represent the two hot legs?
• Which statement about Star-Delta starters is true?
• How efficient are radiant heaters?
• What does equipment rating labeling on a panelboard indicate?
• What is AFCI protection designed to detect?
• For cables up to 10 mm diameter what is the bend radius factor (f) used?
• What is the purpose of a grounding electrode system in a building's electrical system?
• A Gantt chart, also referred to as a bar chart in some contexts, is used to show which aspect of a project in electrical installations?
• Which statement best describes the factors used to size branch-circuit conductors?
• What is the recommended spacing when two cables are side by side?
• How many outlets are allowed from an unfused spur?
• Which statement about MICC and FP200 is true?
• Why are dead-front panels important for safety?
• Which statement describes a Non-maintained emergency lighting system?
• COSHH stands for which of the following?
• PUWER is the regulation that governs safety standards for the use of what at work?
• Which drawing is used to show a three-dimensional, real-world arrangement of components?
• What distribution voltage is used to step down to 400V/230V in homes?
• What does the term Short-Circuit Current Rating (SCCR) stand for?
• What is the purpose of a pull string in conduit installations?
• RCM stands for which term?
• What does it mean for electrical equipment to be listed?
• What is selectivity in relation to fuses and breakers?
• What is meant by equipotential bonding achieved by bonding a water pipe to the electrical system?
• Why is sizing of the equipment grounding conductor important?
• Which NEC article covers luminaires and lighting outlets?
• What is the maximum length an LAN cable should be without any intervention?
• OCPD stands for which term?
• Which test must be carried out on ring final circuits to ensure they remain continuous, and why?
• Which statement about NM cable is false?
• Single-line diagrams are used to represent what aspect of an electrical installation?
• Which statement describes a feature of BS88 fuses?
• Which MCB type has the highest inrush trip range?
• What quantities can a multimeter measure?
• Which article covers switches?
• Which of the following is not a statutory regulation?
• Which NEC section requires kitchen countertop receptacle outlets?
• Which type of cable is rated for direct burial and outdoor use?
• What does a 'loop in' box accessory look like?
• In a two-plate lighting system, where are the junction boxes located and what connections do they accommodate?
• Are clips holding vertical wiring of 9mm thickness in line with regulation if they are 340mm apart?
• Which appliances in a domestic installation should have their own circuit to the CCU?
• Which statement about ampacity is accurate?
• What is the typical method to verify grounding continuity in a new installation?
• Which statement describes overload?
• What is the purpose of an End-of-Line resistor in monitored circuits?
• Which factors are considered when sizing conductors for a branch circuit?
• Which practice is considered good when arranging MCBs in a CCU?
• Which NEC section governs kitchen countertop receptacle outlets?
• Zs represents the total earth fault loop impedance, calculated as which of the following?
• What is the trip range for a Type B MCB?
• Plan drawings are used to depict what aspect of an electrical installation?
• Which components are typically included in a DOL motor starter for protection?
• What is the maximum distance firefighters should search for a circuit?
• Which of the following is NOT a typical advantage of fiber optic cable?
• What is the maximum fullness allowed for trunking?
• What is the GFCI's built-in test function used for?
• What does voltage regulation mean in power distribution?
• What is the purpose of a two-way conversion lighting circuit?
• What are the two types of emergency lighting systems?
• What length of patch leads is recommended at each end of an LAN cable?
• Which statement about FP200 compared to MICC is true?
• Which statement about PVC is true?
• Which PVC cable type requires additional mechanical protection?
• In a 3-plate lighting arrangement, what does the term loop-in refer to?
• MHOR is the acronym for which Regulations?
• What is the difference between conductors and cables?
• Which material is UV stable?
• What is the function of a pull box?
• What is the purpose of a supplementary protective bonding conductor?
• Which alarm circuits are wired in series?
• What is the cold tail of an underfloor heating system?
• The Manual Handling Operations Regulations were enacted in which year?
• Which circuit type makes tampering most difficult?
• Which sequence describes the correct order of power flow in a CCU from the supply?
• Which pocket-sized help book is published by Unite?
• NOT a type of cable tray is which option?
• Which item is not a true type of cable tray but is a similar carrier?
• What is the primary reason for the 3-plate loop-in method in lighting circuits?
• In a transformer, when voltage is stepped up, what happens to current?
• Do domestic smoke detectors have to be connected to the mains supply?
• Which description correctly defines an extraneous conductive part?
• How does a short circuit differ from an overload?
• Which MCB type has a trip range of 5-10x?
• Which document provides practical guidance on Compliance?
• AFCI/AFDD stands for which term?
• What is a panelboard?
• At what height are pings required in vertical trunking?
• Which statement about ampacity is correct?
• The Electrical Safety, Quality and Continuity Regulations are primarily intended to safeguard which aspect of electrical supply?
• What is the most common form of stored hot water system?
• What is the purpose of the grounding electrode system?
• SCPD stands for which term?
• FP200 may require ferrules (fasteners).
• The general term protective conductors applies to which of the following?
• Which NEC article governs general requirements for electrical installations, including workmanship and safety?
• A bonding conductor is used to connect what?
• Under the Electricity at Work Regulations, which regulation provides a defence in court if you prove you took all reasonable steps and exercised due diligence to avoid an offence?
• Isometric drawings are used to illustrate what?
• What does a service entrance conduit connect?
• Which statement about an overcurrent is correct?
• In a series (closed) alarm circuit, tampering with a detector typically results in what?
• Which of the following is NOT a typical underfloor heating system for standard rooms?
• Which statement best describes voltage regulation in power distribution?
• What is GFCI protection designed to do?
• What is the purpose of a receptacle outlet?
• Which correction factor symbol refers to insulation?
• What document is issued to contractors to tender for electrical installation work?
• Which of the following is an example of an instantaneous water heater appliance?
• What is the difference between grounding and bonding?
• Which article addresses receptacles?
• What is the primary purpose of an RCD?
• RCCB stands for which term?
• What is insulation resistance testing used for?
• What is a three-way switch used for?
• Which single tool is used to bend steel conduits?
• What is NFPA 70E primarily concerned with?
• Which statement best reflects the relationship between discrimination and selectivity?
• An RCBO combines residual current protection with what additional protection?
• GFCI stands for which term?
• What is the typical temperature range of an immersion heater and why is it this level?
• The general term for protective conductors includes which of the following?
• In a 3-plate loop-in arrangement, where is the additional joint typically located?
• What describes a Direct On Line (DOL) starter?
• What does SCCR indicate in electrical equipment?
• What is the difference between branch circuits and feeders?
• NM cable is typically used for?
• Which NEC article covers switches?
• Which insulation type melts under heat after curing and is ideal for recycled materials?
• Conduit fill is defined as what?
• Which conductor is primarily used to provide a safety path to ground for faults in electrical equipment?